boom barrier system
Boom barrier system
The boom barrier system is a channel entrance and exit management equipment specially used for restricting motor vehicles on the road. It is now widely used in highway toll stations, parking lots, communities, and the entrances of enterprises and institutions to manage the entry and exit of vehicles. The electric road gate can realize the landing rod through remote control alone, and can also realize the automatic management state through the parking lot management system (ie IC card swiping management system). According to the use place of the gate, the gate rod can be divided into straight rod, 90-degree curved rod, 180-degree folding rod and fence.
Chinese name The brake system Foreign name The brake system Working environment temperature -40℃～85℃ Rated common rate 70W/150W Relative temperature ≥90%
content
1 Main function
2 Performance characteristics
3 Technical parameters
4 Notes
Main function editing broadcast
1. Computer management system
The system is the core of the entire barrier parking lot management, consisting of computers, printers, communication lines and management software. It mainly completes functions such as IC card verification, monthly card management, control signal reception and transmission, parking time and parking fee calculation, image capture and display, data statistics, and printing reports.
2. Card reader control function at entrance and exit
This part is the necessary basic function of each gate entrance and exit, and it is also the main and core part of each gate entrance and exit.
3. Temporary card automatic card issuing function
This card dispenser is double-layered, which is convenient for large and small vehicles. Temporary parking users can press the "Get Card" button on the card reader box to get the card and enter the parking lot. This function can also be replaced by manual card issuance by the barrier management personnel. The automatic card issuance is strictly controlled for one card per car, and the card cannot be taken without a car. The card reading is completed at the same time as the card is issued, and the card is automatically withdrawn if it is outdated and not taken. Automatic card swallowing function When the temporary card vehicle leaves the field, the system automatically recycles the card and releases it.
4. Anti-smashing car sensing function
The road gate cooperates with the vehicle detector to realize the anti-smashing function. When there is a brake lever under the road barrier, it will not fall. Even if a car drives under it when the brake lever falls, the brake lever will stop falling and lift up. After the vehicle leaves, the brake lever will not fall. The rod falls automatically. At the same time, it can be combined with the pressure wave safety device to achieve double anti-smashing car protection processing.
5. Chinese display function
The LED display of the entrance and exit control box displays welcome words, charge amount, card balance, card validity period, recharge reminder, parking space full and other related information of the parking lot in Chinese. It can also be connected to an independent display screen to release relevant information for the owner to read from different angles and distances.
6. Voice prompt function
The normal operation can prompt the card reading, charging yuan and other related information, and the misuse or illegal operation will give corresponding prompts.
7、Intercom function
Install the intercom host in the monitoring room management center, install the intercom extension at each entrance, and press the intercom button to ensure the connection between each entrance and the monitoring room management center.
8. Image capture and comparison function
Cameras are installed at the entrance and exit. When the vehicle enters from the gate, the image of the vehicle is automatically captured and stored in the computer together with the cardholder and card swiping time. When leaving the venue, the system will automatically call out the entry image of the vehicle holding the card, and the image of the vehicle after exiting the venue. Only after comparing with the image from the gate entrance and confirming that it is the same vehicle, will it be released to ensure the safety of the vehicle.
9. UPS power supply
Improve the quality of power supply and reduce problems caused by power outages and power outages. When the utility grid is suddenly cut off or cut off, the UPS can automatically start the battery to ensure the normal operation of the gate system.
10. Lightning protection function
In order to ensure the normal operation of the gate system and prevent and reduce equipment damage caused by lightning strikes on power supply lines and signal lines, lightning protection of the gate system is required to ensure the normal operation of the equipment [1] .
Performance characteristics edit broadcast
1. Special rotating structure, no gear, no belt rotation, no maintenance, stable use and longer life.
2. The specially designed balance structure makes the brake lever start slowly, run quickly, stop slowly,
3. The vibration caused by the operation of the brake lever is excluded.
4. The brake lever runs 90 degrees permanently, and the accident of 360 degree operation is caused by troubleshooting.
5. Specially designed low-speed aluminum casing motor, gearbox conjoined design, low noise and fast heat dissipation.
6. The drive mechanism is designed with an intelligent overheat protection system, which controls the temperature rise of the motor under frequent use, so that the motor is not easy to burn out
barrier
Edit technical parameters
Working voltage: AC220V±10%50HZ AC110V±10%50HZ/60HZ
Notes Edit Broadcast
1. When the gate is working, it is strictly forbidden to open the box cover and box door to avoid personal accidents.
2. The gate has been wired in the box before leaving the factory. Under normal circumstances, the user cannot change it. It only needs to connect to the 220V power supply to work.
3. The power supply of this machine must be equipped with a leakage breaker of ≥15A.
4. When dropping the rod, it is forbidden to place items under the blocking rod or to stand or walk.
5. In the event of a power failure, the power should be turned off first and then manually swing the brake lever to the vertical position.
6. When the product leaves the factory, the length of the blocking rod and the balance spring have been adjusted to the best state. Do not increase or decrease the length and weight of the blocking rod at will, so as to avoid the danger of losing balance. If you need to change it, you must ask a professional to operate it.
7. The mechanical switch limit and photoelectric switch limit have been adjusted to the best state before leaving the factory, and should not be adjusted at will
