Common faults and solutions of tripod turnstile
Common faults and solutions of tripod turnstile
Tripod turnstile access control and swing gates are now widely used in many places. In the process of use, some failures will inevitably occur. So how should we solve it? Next, I will give you a detailed introduction to the common faults and treatment methods of the tripod turnstile and the swing gate.
Common troubleshooting methods for tripod gates and swing gates during ticket inspection
One: What should I do if the tripod turnstile or swing gate cannot be opened after swiping the card or checking the ticket?
1. It is possible that a pedestrian has withstood the rotating rod when swiping the card or checking the ticket. Please take a step back and then swipe the card.
2. Please check whether the electromagnet is normal. If the voltage of the electromagnet is output in the control part, and the voltage is normal, but the electromagnet cannot be picked up, just replace the electromagnet.
2. How to deal with how many people can pass through the tripod turnstile after swiping or checking the ticket?
1. Check whether the proximity switch and the induction screw on the proximity switch bracket are loose. Under normal circumstances, when a person passes normally, the induction screw will contact the induction proximity switch, and the induction lamp on the induction proximity switch will light up. If the light is not on, use a multimeter to measure whether the input power of the proximity switch is normal. If it is normal, replace the proximity switch.
2. In the case that the proximity switch is not broken and the card is read, check whether the electromagnet is reset. If not, remove the electromagnet, check whether there is any foreign matter inside the electromagnet and deal with it. If there is no foreign matter, you can increase the strength of the spring inside the electromagnet, but not too much. If it is too large, the electromagnet cannot be attracted.
3. What should I do if there is no response when the tripod turnstile is swiping the card?
1. Check whether the ticket used is the ticket of this system and whether the ticket verification method is correct.
2. Check whether the connection of the card reader is normal. If it is a barcode ticket, please check whether the card is inserted backwards, check whether the connection of the card reader unit is normal, and whether the angle of the barcode reader is accurate.
3. Check whether the key trigger board is normal.
4. What should I do if the response speed of the tripod turnstile ID card is slow when swiping?
1. The parameter setting is wrong, the problem is solved after correct setting
Trouble shooting method of rotating rod during operation of tripod turnstile and swing gate
1. Tripod turnstile, what should I do if the rotating rod cannot be lifted after the swing gate is energized?
1. Press the rotating rod down to the end and then lift it up.
2. Open the cover of the gate, check whether the circlip on the electromagnet device of the lever falls off, whether the circlip is in close contact with the electromagnet when the lever is pressed to the end, if not, you need to readjust the installation position of the electromagnet.
3. Check whether the electromagnet is damaged. Use a multimeter to measure whether there is a supply voltage (24V). If there is a voltage, there is no problem with the above checks, please replace the electromagnet; if there is no voltage, please check whether the output part of the control drive board is normal.
2. What should I do if the tripod turnstile has individual gates and the bar is dropped?
1. The position of the pole drop solenoid is not installed properly, install it in the correct way.
2. Power supply problem, insufficient voltage, overhaul the circuit to ensure that the voltage is normal.
3. What should I do if the turnstile is powered off but the pole does not fall?
1. Check whether the installation position of the electromagnet is correct, and the spring force of the falling pole electromagnet bracket is too small, adjust it in time.
2. The friction between the turntable and the rotating rod is too large, and the maintenance should be carried out in accordance with the maintenance guide during normal maintenance.
Trouble shooting method of turntable during operation of tripod turnstile and swing gate
1. What should I do if the turntable of the tripod turnstile can be reversed sometimes?
Under normal circumstances, you can only enter after checking a valid ticket, and you cannot reverse it. If reversal occurs:
1. Check whether the stop pin is reset. Open the cover of the gate first, add some lubricating oil to the stop pin, and then pull the stop pin back and forth to make it completely lubricated. You can also remove the car stop bracket, take out the car stop pin and clean the burrs with a file, then assemble it back, add liquid lubricating oil, and pull the car stop pin back and forth to make it fully movable.
2. It may be that the performance of the buffer is unstable and the turntable cannot be reset. You can adjust the strength of the buffer or replace the buffer.
3. The position of the proximity switch is incorrect, and the turntable cannot be reset, so you need to adjust the position of the proximity switch.
2. How to deal with the swing of the turntable of the gate?
1. The tray of the turntable of the gate is loose, and the gap between the fits is too large. Adjust the gap.
2. If the screws of the gate tray are loose, tighten the screws in time.
Contact information:
